Eco Cleaner Oxygenated Wood Cleaner for environmentally friendly multi purpose cleaner. 8 pounds of powder in a 1 gallon container makes 16 gallons of liquid cleaner. For Fence cleaning, deck cleaning, dock cleaning, etc... Perfect for eco friendly fence or deck cleaning and restoration.
100% Sodium Percarbonate
- Fence cleaning, deck cleaning, dock cleaning, etc
- An eco friendly and mild alkaline cleaner that works well for unsealed, lightly soiled, or faded wood
REAL IMPACT. Restore Wood’s Natural Beauty.
EXPERT Clean & Bright Eco Cleaner is STEP 1 of a 3-STEP system. It is recommended for surface prep prior to application or re-application of wood stains. For best results, use all EXPERT Clean & Bright Professional Wood Care products followed by our EXPERT Stain & Seal wood stains.
REAL PERFORMANCE. Use & Preparation.
EXPERT’s Eco Cleaner kills organic growth, removes dirt, debris, and grime, as well as stains caused by mold and mildew, and weathered graying caused by UV rays. Cleans horizontal, and vertical surfaces.
EXPERT’s Eco Cleaner is a powdered concentrate that is mixed with warm water. It safely cleans and restores the natural beauty of exterior wood. This product also cleans and removes mold, mildew, and algae along with the silver-gray color that can develop over time. EXPERT Clean & Bright Eco Cleaner will not harm wood fibers, pets, grass, or most plants.
TEST AREA: It’s recommended to test the product in a small, inconspicuous area to ensure desired results before use.
LIMITATIONS: EXPERT Clean & Bright Eco Cleaner is not intended to remove intact paint, stain, or clear finishes, and may dull painted or metal surfaces if not rinsed immediately. Always store in a temperature-controlled room, kept from freezing, and can be stored for up to 36 months, unopened.
- Test on a small, inconspicuous area of the wood to ensure proper wood care.
- Apply to surface to be cleaned with a pump up sprayer, 12 volt chemical sprayer or with a bucket and brush.
- Allow the cleaner to dwell for at least 10 minutes, dirty surfaces may need agitated with a brush. Expect to see bubbling on the surface, that means the cleaner is working.
- Always wet plants, shrubs, and other surrounding vegetation before and after use.
- Always brighten the wood after using this cleaner.
- Keep out of reach of children. Exposure to sodium percarbonate could cause irritation to the eyes, skin, or lungs.
- If contact occurs, rinse immediately with water for 15 minutes. If irritation continues, seek immediate medical attention.
- Do not ingest.
- Always wear personal protective equipment when using this product.
- DO NOT MIX WITH OTHER CHEMICALS.
Coverage: 4oz to 8oz of EXPERT Clean & Bright Eco Cleaner will make 1 gallon of cleaning solution and cover approximately 150 to 250 sq. ft. depending on surface and method of application.
REAL APPLICATION. Easy-to-Use & Clean-Up.
Read through all the step-by-step instructions prior to using EXPERT®™ Clean & Bright Eco Cleaner.
MIXING: Always wear heavy-duty rubber gloves, niosh approved respirator and PPE when working with EXPERT Clean & Bright Eco Cleaner, or any other EXPERT Clean & Bright products.
Mix 4oz to 8oz of Eco Cleaner with each gallon of warm water and stir thoroughly until powder is mostly dissolved. Mix in a separate 5-gallon pail before transferring into a pump sprayer. This avoids clogging the sprayer. Use Cleaner solution within 4 hours of mixing. Eco Cleaner mixed solution is Green in color for ease of identification.
APPLICATION: Pre wet the surface with water before application. Apply EXPERT Clean & Bright Eco Cleaner solution with a sprayer, brush, or car wash brush, working on small areas (100-200 sq. ft.) at a time.
If applying cleaner on vertical surfaces using a sprayer, work on small areas at a time, starting at the bottom, and working your way up.
If needed, scrub thoroughly with a hard, short, bristled broom, or brush. Be sure to keep the area wet with additional solution or mist from a water hose and allow the eco cleaner to sit for approximately 5 to 20 minutes or until the desired result is achieved.
RINSE: Rinse thoroughly with water from a hose or pressure washer using lowest effective pressure, to clean without damaging the wood. For extreme build up of dirt, or organic growth use either a power washer, or a hard bristled brush. While using a power washer, use only the minimum effective amount of pressure to achieve the desired result. Particular care should be taken in order to not damage the wood, power wash using a pendulum motion the full length of each board. Do not start and stop as scarring or gouging of wood can occur.
NEUTRALIZE: After cleaning is complete, immediately neutralize and brighten the wood using EXPERT Clean & Bright Wood Brightener. Let EXPERT Wood Brightener sit for 5 to 15 minutes ensuring the entire surface has been properly neutralized and rinsed thoroughly. A color change will be evident when properly brightened, this will open wood grain and prevent poor stain penetration.
IMPORTANT: After Brightener is applied, rinse wood’s entire surface for 10 to 15 minutes, and rinse all nearby surfaces including siding, windows, and foliage.
Allow wood surfaces to dry 48 to 72 hours (or longer) before applying EXPERT Stain & Seal wood stains. Stains must be applied when wood is dried to 13% moisture content or less.
Clean-up: Clean tools and equipment immediately after each use with soap and water.
QUESTIONS & ANSWERS
Have a Question?
Be the first to ask a question about this.